Additions:
>>{{sourcebigbox}}
{{youtubecylinderhead}}>> {{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Deletions:
>>{{sourcebigbox}}>> {{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Additions:
>>{{source1}}>> {{sourcebigbox2}}
==''REMOVAL''==
[[GeneralAutoRepair General Automotive Repair]]
{{linkunit2}}
Deletions:
>>{{source1}}>> ==''REMOVAL''==
{{sourcebigbox2}}
Additions:
{{sourcebigbox2}}
==''LIFTERS''==
Deletions:
>>{{source1}}>> ==''LIFTERS''==
Additions:
>>{{sourcebigbox}}>> {{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Deletions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}} {{source2}}
Additions:
=====''Cylinder Head Overhaul - removal, cleaning, inspection and installation''=====
Deletions:
=====''Cylinder Head replacement and overhaul''=====
Additions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}} {{source2}}
>>{{source1}}>> ==''LIFTERS''==
Deletions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
{{source4}}
==''LIFTERS''==
{{source4}}
Additions:
>>{{source1}}>> ==''REMOVAL''==
Deletions:
==''REMOVAL''==
No differences.
Additions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Deletions:
>>{{source2}}>> {{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Additions:
In internal combustion engines, the cylinder head sits above the engine block and consists of a platform containing part of the combustion chamber and the location of the valves and spark plugs. In a flathead engine, the mechanical parts of the valve train are all contained within the block, and the head is essentially a flat plate of metal bolted to the top of the cylinder bank with a head gasket in between; this simplicity leads to ease of manufacture and repair, and accounts for the flathead engine's early success in production automobiles and continued success in small engines, such as lawnmowers. This design, however, requires the incoming air to flow through a convoluted path, which limits the ability of the engine to perform at higher rpm, leading to the adoption of the overhead valve head design.
In the overhead valve head (OHV), the top half of the cylinder head contains the camshaft in an overhead cam engine, or another mechanism (such as rocker arms and pushrods) to transfer rotational mechanics from the crankshaft to linear mechanics to operate the valves (pushrod engines perform this conversion at the camshaft lower in the engine and use a rod to push a rocker arm that acts on the valve). Internally the cylinder head has passages called ports for the fuel/air mixture to travel to the inlet valves from the intake manifold, for exhaust gases to travel from the exhaust valves to the exhaust manifold, and for antifreeze to cool the head and engine.
The number of cylinder heads in an engine is a function of the engine configuration. A straight engine has only one cylinder head, for instance inline 4 engines. A V engine usually has two cylinder heads (V6, V8, etc), one at each end of the V, although Volkswagen, for instance, produces a V6 called the VR6, where the angle between the cylinder banks is so narrow that it utilizes a single head. A boxer engine has two heads.
Deletions:
In an internal combustion engine, the cylinder head sits above the cylinders and consists of a platform containing part of the combustion chamber and the location of the valves and spark plugs. In a flathead engine, the mechanical parts of the valve train are all contained within the block, and the head is essentially a flat plate of metal bolted to the top of the cylinder bank with a head gasket in between; this simplicity leads to ease of manufacture and repair, and accounts for the flathead engine's early success in production automobiles and continued success in small engines, such as lawnmowers. This design, however, requires the incoming air to flow through a convoluted path, which limits the ability of the engine to perform at higher rpm, leading to the adoption of the overhead valve head design.
In the overhead valve head, the top half of the cylinder head contains the camshaft in an overhead cam engine, or another mechanism (such as rocker arms and pushrods) to transfer rotational mechanics from the crankshaft to linear mechanics to operate the valves (pushrod engines perform this conversion at the camshaft lower in the engine and use a rod to push a rocker arm that acts on the valve). Internally the cylinder head has passages called ports for the fuel/air mixture to travel to the inlet valves from the intake manifold, for exhaust gases to travel from the exhaust valves to the exhaust manifold, and for antifreeze to cool the head and engine.
The number of cylinder heads in an engine is a function of the engine configuration. A straight engine has only one cylinder head. A V engine usually has two cylinder heads, one at each end of the V, although Volkswagen, for instance, produces a V6 called the VR6, where the angle between the cylinder banks is so narrow that it utilizes a single head. A boxer engine has two heads.
Additions:
>>{{source2}}>> {{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
{{source4}}
{{source4}}
Deletions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Additions:
=====''Cylinder Head replacement and overhaul''=====
Deletions:
=====''Cylinder Head replacement and overhaul (beta)''=====
Additions:
Valve stem oil seals must be installed on valve stem. [[http://www.tunerselect.com/garage411/images/GeneralAuto/ValveAssembly.gif See figure]]. Seals are needed due to pressure differential at the ends of valve guides. Atmospheric pressure above intake guide, combined with manifold vacuum below guide, causes oil to be drawn into the cylinder.
''Replacement (On-Vehicle)''
Mark rocker arm or overhead cam components for location. Remove rocker arm components or overhead cam components. Components must be installed in original location. Remove spark plugs. Valve stem oil seals may be replaced by holding valves against seats using air pressure.
Air pressure must be installed in cylinder using an adapter for spark plug hole. An adapter can be constructed by welding air hose connection to spark plug body with porcelain removed.
Rotate engine until piston is at top of stroke. Install adapter in spark plug hole. Apply a minimum of 140 psi (9.8 kg/cm2 ) line pressure to adapter. Air pressure should hold valve closed. If air pressure does not hold valve closed, check for damaged or bent valve. Cylinder head must be removed for service.
Using valve spring compressor, compress valve springs. Remove valve locks. Carefully release spring compressor. Remove retainer or rotator and valve spring. Remove valve stem oil seal.
If oversize valves have been installed, oversize oil seals must be used. Coat valve stem with engine oil. Install protective sleeve over end of valve stem. Install new oil seal over valve stem and seat on valve guide. Remove protective sleeve. Install spring seat, valve spring and retainer or rotator. Compress spring and install valve locks. Remove spring compressor. Ensure valve locks are fully seated.
Install rocker arms or overhead cam components. Tighten all bolts to specification. Adjust valves if required. Remove adapter. Install spark plugs, valve cover and gasket.
''VALVE SPRING INSTALLED HEIGHT''
Valve spring installed height should be checked during reassembly. Measure height from lower edge of valve spring to the upper edge. DO NOT include valve spring seat or retainer. Distance must be within specification. If valves and/or seats have been ground, a valve spring shim may be required to correct spring height. [[http://www.tunerselect.com/garage411/images/GeneralAuto/ValveSpringHeight.gif See Figure]].
==''ROCKER ARMS & ASSEMBLIES''==
''Rocker Studs''
Rocker studs are either threaded or pressed in place. Threaded studs are removed by locking 2 nuts on the stud. Unscrew the stud by turning the jam nut. Coat new stud threads with Loctite and install. Tighten to specification.
Pressed-in stud can be removed using a stud puller. Ream stud bore to proper specification and press in a new oversize stud. Pressed-in studs are often replaced by cutting threads in the stud bore to accept a threaded stud.
''Rocker Arms & Shafts''
Mark rocker arms for location. Remove rocker arm retaining bolts. Remove rocker arms. Inspect rocker arms, shafts, bushings and pivot balls (if equipped) for excessive wear. Inspect rocker arms for wear in valve stem contact area. Measure rocker arm bushing I.D. Replace bushings if excessively worn.
The rocker arm valve stem contact point may be reground, using special fixture for valve grinding machine. Remove minimum amount of material as possible. Ensure all oil passages are clear. Install rocker arm components in original location. Ensure rocker arm is properly seated in push rod. Tighten bolts to specification. Adjust valves if required.
==''PUSH RODS''==
Remove rocker arms. Mark push rods for location. Remove push rods. Push rods can be steel or aluminum, solid or hollow. Hollow push rods must be internally cleaned to ensure oil passage to rocker arms is cleaned. Check push rods for damage, such as loose ends on steel tipped aluminum types.
Check push rod for straightness. Roll push rod on a flat surface. Using feeler gauge, check clearance at center. Replace push rod if bent. The push rod can also be supported at each end and rotated. A dial indicator is used to detect a bent area in the push rod.
Lubricate ends of push rod and install push rod in original location. Ensure push rod is properly seated in lifter. Install rocker arm. Tighten bolts to specification. Adjust valves if required.
==''LIFTERS''==
''Hydraulic Lifters''
Before replacing a hydraulic lifter for noisy operation, ensure noise is not caused by worn rocker arms or valve tips. Also ensure sufficient oil pressure exists. Hydraulic lifters must be installed in original location. Remove rocker arm assembly and push rod. Mark components for location. Some applications require intake manifold, cylinder head or lifter cover removal. Remove lifter retainer plate (if used). To remove lifters, use a hydraulic lifter remover or magnet. Different type lifters are used.
On sticking lifters, disassemble and clean lifter. DO NOT mix lifter components or positions. Parts are selectfitted and are not interchangeable. Inspect all components for wear. Note amount of wear in lifter body-tocamshaft contact area. Surface must have smooth and convex contact face. If wear is apparent, carefully inspect cam lobe.
Inspect push rod contact area and lifter body for scoring or signs of wear. If body is scored, inspect lifter bore for damage and lack of lubrication. On roller type lifters, inspect roller for flaking, pitting, loss of needle bearings and roughness during rotation.
Measure lifter body O.D. in several areas. Measure lifter bore I.D. Ensure components or oil clearance is within specification. Some models offer oversize lifters. Replace lifter if damaged.
If lifter check valve is not operating, obstructions may be preventing it from closing or valve spring may be broken. Clean or replace components as necessary.
Check plunger operation. Plunger should drop to bottom of the body by its own weight when assembled dry. If plunger is not free, soak lifter in solvent to dissolve deposits.
Lifter leak-down test can be performed on lifter. Lifter must be filled with special test oil. New lifters contain special test oil. Using lifter leak-down tester, perform leak-down test following manufacturer's instructions. If leak-down time is not within specifications, replace lifter assembly.
Lifters should be soaked in clean engine oil several hours prior to installation. Coat lifter base, roller (if equipped) and lifter body with ample amount of Molykote or camshaft lubricant. Install lifter in original location. Install remaining components. Valve lash adjustment is not required on most hydraulic lifters. Preload of hydraulic lifter is automatic. Some models may require adjustment.
**FYI:** Some manufacturers require that a crankcase conditioner be added to engine oil and engine operated for specified amount of time to aid in lifter break-in procedure if new lifters or camshaft are installed.
''Mechanical Lifters''
Lifter assemblies must be installed in original locations. Remove rocker arm assembly and push rod. Mark components for location. Some applications require intake manifold or lifter cover removal. Remove lifter retainer plate (if used). To remove lifters, use lifter remover or magnet.
Inspect push rod contact area and lifter body for scoring or signs of wear. If body is scored, inspect lifter bore for damage and lack of lubrication. Note amount of wear in lifter body-to-camshaft contact area. Surface must have smooth and convex contact face. If wear is apparent, carefully inspect cam lobe.
Coat lifter base, roller (if equipped) and lifter body with ample amount of Molykote or camshaft lubricant. Install lifter in original location. Install remaining components. Tighten bolts to specification. Adjust valves.
Deletions:
Valve stem oil seals must be installed on valve stem. See Fig. 2 . Seals are needed due to pressure differential at the ends of valve guides. Atmospheric pressure above intake guide, combined with manifold vacuum below guide, causes oil to be drawn into the cylinder.
Additions:
''Valve Seat Replacement''
Replacement of valve seat inserts is done by cutting out the old insert and machining an oversize insert bore. Replacement oversize insert is usually cooled and the cylinder head is sometimes warmed. Valve seat is pressed into the head. This operation requires specialized machine shop equipment.
''Valve Seat Concentricity''
Using dial gauge, install gauge pilot in valve guide. Position gauge arm on the valve seat. Adjust dial indicator to zero. Rotate arm 360 degrees and note reading. Runout should not exceed specification.
To check valve-to-valve seat concentricity, coat valve face lightly with Prussian Blue dye. Install valve and rotate it on valve seat. If pattern is even and entire seat is coated at valve contact point, valve is concentric with the valve seat.
==''CYLINDER HEAD REASSEMBLY''==
''Valve Stem Installed Height''
Valve stem installed height must be checked when new valves are installed or when valves or valve seats have been ground. Install valve in valve guide. Measure distance from tip of valve stem to spring seat. [[http://www.tunerselect.com/garage411/images/GeneralAuto/ValveStemHeight.gif See Figure]]. Distance must be within specification to allow sufficient clearance for valve operation.
Remove valve and grind valve stem tip if height exceeds specification. Valve tips are surface hardened. DO NOT remove more than .010" (.25 mm) from tip. Chamfer sharp edge of reground valve tip. Recheck valve stem installed height.
''VALVE STEM OIL SEALS''
Valve stem oil seals must be installed on valve stem. See Fig. 2 . Seals are needed due to pressure differential at the ends of valve guides. Atmospheric pressure above intake guide, combined with manifold vacuum below guide, causes oil to be drawn into the cylinder.
Exhaust guides also have pressure differential created by exhaust gas flowing past the guide, creating a low pressure area. This low pressure area draws oil into the exhaust system.
Some manufacturers require that special color code or specified height valve stem oil seal be installed in designated area.
Additions:
''Measuring Valve Guide Clearance''
Check valve stem-to-guide clearance. Ensure valve stem diameter is within specification. Install valve in valve guide. Install dial indicator assembly on cylinder head with tip resting against valve stem just above valve guide. [[http://www.garage411.com/images/GeneralAuto/ValveStemCl.jpg See figure]].
Lower valve approximately 1/16" below valve seat. Push valve stem against valve guide as far as possible. Adjust dial indicator to zero. Push valve stem in opposite direction and note reading. Clearance must be within specification.
If valve guide clearance exceeds specification, valves with oversize stems may be used and valve guides are reamed to larger size or valve guide must be replaced. On some applications, a false guide is installed, then reamed to proper specification. Valve guide reamer set is used to ream valve guide to obtain proper clearance for new valve.
''Reaming Valve Guide''
Select proper reamer for size of valve stem. Reamer must be of proper length to provide clean cut through entire length of valve guide. Install reamer in valve guide and rotate to cut valve guide. [[http://www.tunerselect.com/garage411/images/GeneralAuto/ReamValve.gif See figure]].
''Replacing Valve Guide''
Replace valve guide if clearance exceeds specification. Valve guides are either pressed, hammered or shrunk in place, depending upon cylinder head design and type of metal used.
Remove valve guide from cylinder head by pressing or tapping on a stepped drift. [[http://www.garage411.com/images/GeneralAuto/ValveGuideRI.gif See figure]]. Once valve guide is installed, distance from cylinder head to top of valve guide must be checked. This distance must be within specification.
Aluminum heads are often heated before installing valve guide. Valve guide is sometimes cooled in dry ice prior to installation. Combination of a heated cylinder head and cooled valve guide ensures a tight guide fit upon assembly. The new guide must be reamed to specification.
==''VALVES & VALVE SEATS''==
''Valve Grinding''
Valve stem O.D. should be measured in several areas to indicate amount of wear. Replace valve if not within specification. Valve margin area should be measured to ensure that valve can be ground. [[http://www.garage411.com/images/GeneralAuto/ValveHeadMargin.gif See figure]].
If valve margin is less than specification, the valves will be burned. Valve must be replaced. Due to minimum margin dimensions during manufacture, some new type valves cannot be reground. Some manufacturers use stellite coated valves that must NOT be machined. Valves can only be lapped into valve seat.
**FYI:** Some valves are sodium filled. Extreme care must be used when disposing of damaged or worn sodium-filled valves.
Resurface valve to proper angle specification using valve grinding machine. Follow manufacturer's instructions for valve grinding machine. Specifications may indicate a different valve face angle than seat angle. Measure valve margin after grinding. Replace valve if not within specification. Valve stem tip can be refinished using valve grinding machine.
''Valve Lapping''
During valve lapping of recently designed valves, be sure to follow manufacturer's recommendations. Surface hardening and materials used with some valves do not permit lapping. Lapping process will remove excessive amounts of the hardened surface.
Valve lapping is done to ensure adequate sealing between valve face and seat. Use either a hand drill or lapping stick with suction cup attached.
Moisten and attach suction cup to valve. Lubricate valve stem and guide. Apply a thin coat of fine valve grinding compound between valve and seat. Rotate lapping tool between the palms or with hand drill. Lift valve upward off the seat and change position often. This is done to prevent grooving of valve seat. Lap valve until a smooth polished seat is obtained. Thoroughly clean grinding compound from components. Valveto-valve seat concentricity should be checked.
**FYI:** Valve guides must be in good condition and free of carbon deposits prior to valve seat grinding. Some engines contain an induction hardened valve seat. Excessive material removal will damage valve seats.
''Valve Seat Grinding''
Select coarse stone of correct size and angle for seat to be ground. Ensure stone is true and has a smooth surface. Select correct size pilot for valve guide dimension. Install pilot in valve guide. Lightly lubricate pilot shaft. Install stone on pilot. Move stone off and on the seat approximately 2 times per second during grinding operation.
Select a fine stone to finish grinding operation. Various angle grinding stones are used to center and narrow the valve seat as required. [[http://www.tunerselect.com/garage411/images/GeneralAuto/AdjValveSeat.gif See figure]].
Deletions:
More content coming soon...
Additions:
{{image url="http://www.garage411.com/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Deletions:
{{image url="http://www.tunerselect.com/garage411/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
Additions:
{{image url="http://www.tunerselect.com/garage411/images/GeneralAuto/cylinderhead.jpg" title="head" alt="cylinder head"}}
No differences.
Additions:
====''CYLINDER HEAD OVERHAUL''====
Deletions:
===''CYLINDER HEAD OVERHAUL''===