Additions:
=====''Honda S2000 Dashboard Removal and Installation''=====
Deletions:
>>{{source1}}>> =====''Honda S2000 Dashboard Removal and Installation''=====
Additions:
[[HondaS2000 Honda S2000 2000-2004 AP1]]
Deletions:
[[HondaS2000 Honda S2000 2000-20004 AP1]]
Additions:
>>{{source1}}>> =====''Honda S2000 Dashboard Removal and Installation''=====
{{sourcebigbox2}}
{{sourcebigbox2}}
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Deletions:
=====''Honda S2000 Dashboard Removal and Installation''=====
{{source4}}
{{source4}}
Additions:
**CAUTION:** SRS components are located in this area.
4. Disconnect the engine wire harness connector, engine compartment wire harness connectors, door wire harness connectors, rear wire harness connector, steering hanger beam wire harness connectors, SRS main harness connector, radio antenna harness connector, ECM connector, keyless entry control unit connector, and convertible top control unit connector. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]].
5. Remove the ground bolts.
7. Open the doors, remove the caps ([[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]]), then remove the bolts and screws, and lift up on the dashboard to release it from the guide pins. Take care not to scratch the center console and shift knob.
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
Honda S2000 2000-2004 interior dashboard removal and installation
**CAUTION:** SRS components are located in this area. Review the SRS component locations, and the precautions and procedures in [[AirBagS2k Air Bag Restraint Systems]] article before performing repairs or service.
4. Disconnect the engine wire harness connector (A), engine compartment wire harness connectors (B), door wire harness connectors (C), rear wire harness connector (D), steering hanger beam wire harness connectors (E), SRS main harness connector (F), radio antenna harness connector (G), ECM connector (H), keyless entry control unit connector (I), and convertible top control unit connector (J). [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]].
5. Remove the ground bolts (K).
7. Open the doors, remove the caps (A) ([[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]]), then remove the bolts (B, C, D) and screws (E), and lift up on the dashboard (F) to release it from the guide pins (G). Take care not to scratch the center console and shift knob.
Additions:
5. Remove the ground bolts (K).
Deletions:
>>{{source2}}>> 5. Remove the ground bolts (K).
Additions:
>>{{source2}}>> 5. Remove the ground bolts (K).
Deletions:
5. Remove the ground bolts (K).
{{sourceslim}}
Additions:
{{source4}}
Tool needed
Deletions:
Tool needed >>{{source2}}>>
Additions:
{{sourceslim}}
Additions:
Tool needed >>{{source2}}>>
Deletions:
Tool needed
No differences.
Additions:
Tool needed
~-KTC trim tool set SOJATP2014
~-[[GaugeClusterS2k Gauge Cluster]]
~-[[AudioS2k Radio panel]]
~-[[ConsoleS2k Passenger's dashboard lower cover]]
~-[[ConsoleS2k Front console cover, both sides]]
~-[[ConsoleS2k Passenger's airbag assembly]]
Deletions:
**Gauge Cluster Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the dashboard and related parts.
1. Remove the instrument panel as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard1.gif See image]].
2. Install the panel in the reverse order of removal, and note these items:
~-Replace any damaged clips.
~-Push the clips into place securely.
**Radio Panel Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the dashboard and related parts.
1. Remove the radio panel as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard2.gif See image]].
2. Install the panel in the reverse order of removal, and note these items:
~-Replace any damaged clips.
~-Push the clips into place securely.
**Front Console Cover Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the dashboard and related parts.
1. Remove the front console cover as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard3.gif See image]].
2. Install the cover in the reverse order of removal, and note these items:
~-Replace any damaged clips.
~-Push the clips into place securely.
**Passenger's Door Lower Cover Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the dashboard and related parts.
1. Remove the passenger's dashboard lower cover as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard4.gif See image]].
2. Install the cover in the reverse order of removal, and note these items:
~-Replace any damaged clips.
~-Push the clips into place securely.
**Passenger's Side Vent Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Take care not to scratch the dashboard and related parts.
1. Carefully insert a trim tool next to the clips (A), and detach the clips by prying on the passenger's side vent (B). [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard5.gif See image]]. Take care not to scratch the dashboard and related parts.
2. Remove the vent by releasing the hooks (C).
3. Reinstall the hook portions of the vent first, then push the clips into place securely.
**Dashboard Removal and Installation**
Tool needed: KTC trim tool set SOJATP2014
~-Radio panel
~-Passenger's dashboard lower cover
~-Front console cover, both sides
~-Passenger's airbag assembly
Additions:
=====''Honda S2000 Dashboard Removal and Installation''=====
Deletions:
=====''Honda S2000 Dashboard''=====
Additions:
8. Carefully remove the dashboard through the front door opening.
9. Install the dashboard in the reverse order of removal, and note these items:
~-Make sure the dashboard fits onto the guide pins correctly.
~-Before tightening the bolts, make sure the dashboard wire harness and steering hanger beam wire harness are not pinched.
~-Reconnect the negative cable to the battery.
~-Enter the anti-theft code for the radio, then enter the customer's radio station presets.
~-Reset the clock
~-Do the PCM idle learn procedure
[[HondaS2000 Honda S2000 2000-20004 AP1]]
Additions:
1. Carefully insert a trim tool next to the clips (A), and detach the clips by prying on the passenger's side vent (B). [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard5.gif See image]]. Take care not to scratch the dashboard and related parts.
2. Remove the vent by releasing the hooks (C).
3. Reinstall the hook portions of the vent first, then push the clips into place securely.
**Dashboard Removal and Installation**
**NOTE:** Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. Have an assistant help you when you remove and install the dashboard. Take care not to scratch the dashboard, body and other related parts. Put on gloves to protect your hands.
**CAUTION:** SRS components are located in this area. Review the SRS component locations, and the precautions and procedures in [[AirBagS2k Air Bag Restraint Systems]] article before performing repairs or service.
1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the radio's preset buttons.
2. Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
3. Remove these items:
~-Radio panel
~-Audio unit
~-Steering column
~-Passenger's dashboard lower cover
~-Front console cover, both sides
~-Passenger's airbag assembly
~-Kick panel, both sides
~-Front pillar trim, both sides
4. Disconnect the engine wire harness connector (A), engine compartment wire harness connectors (B), door wire harness connectors (C), rear wire harness connector (D), steering hanger beam wire harness connectors (E), SRS main harness connector (F), radio antenna harness connector (G), ECM connector (H), keyless entry control unit connector (I), and convertible top control unit connector (J). [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]].
5. Remove the ground bolts (K).
6. Detach all of the harness and connector clips.
7. Open the doors, remove the caps (A) ([[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard6.gif See image]]), then remove the bolts (B, C, D) and screws (E), and lift up on the dashboard (F) to release it from the guide pins (G). Take care not to scratch the center console and shift knob.
Deletions:
1. Carefully insert a trim tool next to the clips (A), and detach the clips by prying on the passenger's side vent (B). Take care not to scratch the dashboard and related parts. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard5.gif See image]].
Additions:
**Front Console Cover Removal and Installation**
1. Remove the front console cover as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard3.gif See image]].
2. Install the cover in the reverse order of removal, and note these items:
**Passenger's Door Lower Cover Removal and Installation**
1. Remove the passenger's dashboard lower cover as shown. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard4.gif See image]].
2. Install the cover in the reverse order of removal, and note these items:
**Passenger's Side Vent Removal and Installation**
1. Carefully insert a trim tool next to the clips (A), and detach the clips by prying on the passenger's side vent (B). Take care not to scratch the dashboard and related parts. [[http://www.garage411.com/images/Honda/Ap1/accessories/Dashboard5.gif See image]].
Additions:
----
No differences.