Garage411 : DriveShaftS13

Revision [3584]

Last edited on 2009-07-08 19:09:08 by FreeMan [revised]

No differences.

Revision [3431]

Edited on 2009-07-06 17:49:08 by Spartanic23 [revised]
Additions:
=====''Nissan 240sx Driveshaft: inspection ,installation, removal and more''=====
Deletions:
>>{{source1}}>> =====''Nissan 240sx Driveshaft: inspection ,installation, removal and more''=====
{{sourcebigbox2}}r

Revision [3343]

Edited on 2009-06-30 20:48:39 by FreeMan [revised]
Additions:
>>{{source1}}>> =====''Nissan 240sx Driveshaft: inspection ,installation, removal and more''=====
Deletions:
>>{{source1}}>> =====''Nissan 240sx Driveshaft: measuring points, ''=====

Revision [3205]

Edited on 2009-06-21 14:34:48 by Spartanic23 [revised]
Additions:
>>{{source1}}>> =====''Nissan 240sx Driveshaft: measuring points, ''=====
{{sourcebigbox2}}
===''SPECIFICATIONS''===
{{sourcebigbox2}}r
{{linkunit2}}
Deletions:
=====''Nissan 240sx Driveshaft: measuring points, ''=====
{{source4}}
{{source4}}
>>{{sourcebigbox}}>> ===''SPECIFICATIONS''===

Revision [2895]

Edited on 2009-06-17 17:26:30 by FreeMan [revised]
Additions:
=====''Nissan 240sx Driveshaft: measuring points, ''=====
===''DRIVE SHAFT VIBRATION''===
===''APPEARANCE CHECKING''===
===''INSPECTION''===
==''FRONT AND REAR DRIVE SHAFT''==
1. Inspect drive shaft runout. If runout exceeds specifications, replace drive shaft assembly. Runout limit: 0.024" (0.6 mm).
2. Inspect journal axial play. If the play exceeds specifications, replace drive shaft assembly. Journal axial play: 0" (0 mm).
===''DRIVE SHAFT REMOVAL AND INSTALLATION''===
**1989-1990 MODEL**
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif" title="text" alt="text"}}
**1992-1994 MODEL**
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif" title="text" alt="text"}}
1. Put matchmarks on flanges, and separate 2nd tube from 1st tube.
2. Put matchmarks on the flange and shaft.
>>{{sourcebigbox}}>> ===''SPECIFICATIONS''===
==''DRIVE SHAFT SPECIFICATIONS (M/T 3S63A-R AND A/T 3S63A-T)''==
**SPECIAL TOOLS**
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
=====''Nissan 240sx Driveshaft''=====
==''DRIVE SHAFT VIBRATION''==
==''APPEARANCE CHECKING''==
====''INSPECTION''====
==''FRONT & REAR DRIVE SHAFT''==
1. Inspect drive shaft runout. If runout exceeds specifications, replace drive shaft assembly. Runout limit: 0.024" (0.6 mm). See following image.
2. Inspect journal axial play. If the play exceeds specifications, replace drive shaft assembly. Journal axial play: 0" (0 mm). See following image.
====''REMOVAL AND INSTALLATION''====
==''DRIVE SHAFT''==
**Removal and Installation**
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1]] for 1989-1990 model and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2]] for 1992-1994 model.
1. Put matchmarks on flanges, and separate 2nd tube from 1st tube. See the following image:
2. Put matchmarks on the flange and shaft. See the following image:
>>{{sourcebigbox}}>> ====''SPECIFICATIONS''====
==''DRIVE SHAFT SPECIFICATIONS (M/T 3S63A-R & A/T 3S63A-T)''==
==''SPECIAL TOOLS''==

Revision [1533]

Edited on 2009-05-02 00:16:15 by Spartanic23
Additions:
==''DRIVE SHAFT VIBRATION''==
>>{{sourcebigbox}}>> ====''SPECIFICATIONS''====
Deletions:
>>{{sourceslim}}>> ==''DRIVE SHAFT VIBRATION''==
====''SPECIFICATIONS''====

Revision [1329]

Edited on 2009-04-30 18:14:00 by Spartanic23
Additions:
>>{{sourceslim}}>> ==''DRIVE SHAFT VIBRATION''==
Deletions:
==''DRIVE SHAFT VIBRATION''==

Revision [1124]

Edited on 2009-04-27 20:47:08 by Spartanic23
Additions:
{{source4}}
{{source4}}

Revision [946]

Edited on 2009-04-21 17:29:49 by MasterBlaster
Additions:
====''SPECIFICATIONS''====

Revision [945]

Edited on 2009-04-21 17:28:59 by MasterBlaster
Additions:
==''DRIVE SHAFT SPECIFICATIONS (M/T 3S63A-R & A/T 3S63A-T)''==
==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1990-91)''==

==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1992-94)''==
==''SPECIAL TOOLS''==
Deletions:
====''DRIVE SHAFT SPECIFICATIONS (M/T 3S63A-R & A/T 3S63A-T)''====
====''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1990-91)''====
====''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1992-94)''====
====''SPECIAL TOOLS''====

Revision [944]

Edited on 2009-04-21 17:28:31 by MasterBlaster
Additions:
**Assembly**
1. When installing center bearing, position the "F" mark on center bearing toward front of vehicle. See the following image:
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle9.gif" title="text" alt="text"}}
2. Apply a coat of multi-purpose lithium grease containing molybdenum disulfide to the end face of the center bearing and both sides of the washer.
3. Stake the nut. Always use new one.
4. Align matchmarks when assembling tubes.
====''DRIVE SHAFT SPECIFICATIONS (M/T 3S63A-R & A/T 3S63A-T)''====
~-Number Of Joints: 3
~-Coupling Method With Transmission: Sleeve Type
~-Type Of Journal Bearings: Shell Type (Non-disassembly Type)
~-Distance Between Yokes: 2.480" (63.0 mm)
~-Drive Shaft Runout Limit: 0.024" (0.6 mm)
~-Journal Axial Play: 0" (0 mm)
====''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1990-91)''====
~-Companion Flange-To-Front Drive Shaft Nut: 181-217 (245-294)
~-Center Bearing Lower Mounting Bracket Bolts: 19-29 (25-39)
~-Center Companion Flange Nuts: 25-33 (34-44)
~-Rear Companion Flange Nuts: 29-33 (39-44)
====''TORQUE SPECIFICATIONS Ft. Lbs. (N.m) (1992-94)''====
~-Companion Flange-To-Front Drive Shaft Nut (Replace fastener after disassembly. Use new fastener): 181-217 (245-294)
~-Center Bearing Lower Mounting Bracket Bolts: 24-28 (32-38)
~-Center Companion Flange Nuts: 25-33 (34-44)
~-Rear Companion Flange Nuts: 29-33 (39-44)
====''SPECIAL TOOLS''====
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle10.gif" title="text" alt="text"}}

Revision [943]

Edited on 2009-04-21 17:24:57 by MasterBlaster
Additions:
====''DISASSEMBLY AND ASSEMBLY''====
==''CENTER BEARING''==
**Disassembly**
1. Put matchmarks on flanges, and separate 2nd tube from 1st tube. See the following image:
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle7.gif" title="text" alt="text"}}
2. Put matchmarks on the flange and shaft. See the following image:
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle8.gif" title="text" alt="text"}}
3. Remove locking nut with Tool (ST38060002). See special tools located on bottom of page.
4. Remove companion flange with puller.
5. Remove center bearing with Tool (ST30031000) and press. See special tools located on bottom of page.

Revision [942]

Edited on 2009-04-21 17:22:01 by MasterBlaster
Additions:
====''REMOVAL AND INSTALLATION''====
Deletions:
====''REMOVAL AND INSTALLATION'====

Revision [941]

Edited on 2009-04-21 17:21:50 by MasterBlaster
Additions:
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1]] for 1989-1990 model and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2]] for 1992-1994 model.
Deletions:
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1]]for 1989-1990 model and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2]]for 1992-1994 model.

Revision [940]

Edited on 2009-04-21 17:21:39 by MasterBlaster
Additions:
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1]]for 1989-1990 model and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2]]for 1992-1994 model.
Deletions:
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1 for 1989-1990 model]] and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2 for 1992-1994 model]].

Revision [939]

Edited on 2009-04-21 17:21:06 by MasterBlaster
Additions:
====''REMOVAL AND INSTALLATION'====
==''DRIVE SHAFT''==
**Removal and Installation**
For removal and installation procedures of the drive shaft refer to [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle5.gif figure 1 for 1989-1990 model]] and [[http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle6.gif figure 2 for 1992-1994 model]].

Revision [938]

Edited on 2009-04-21 17:18:14 by MasterBlaster
Additions:
1. Inspect drive shaft runout. If runout exceeds specifications, replace drive shaft assembly. Runout limit: 0.024" (0.6 mm). See following image.
2. Inspect journal axial play. If the play exceeds specifications, replace drive shaft assembly. Journal axial play: 0" (0 mm). See following image.
Deletions:
1. Inspect drive shaft runout. If runout exceeds specifications, replace drive shaft assembly. Runout limit: 0.024" (0.6 mm). See Fig. 3 .
2. Inspect journal axial play. If the play exceeds specifications, replace drive shaft assembly. Journal axial play: 0" (0 mm). See Fig. 4 .

Revision [937]

Edited on 2009-04-21 17:17:30 by MasterBlaster
Additions:
----
====''INSPECTION''====
==''FRONT & REAR DRIVE SHAFT''==
1. Inspect drive shaft runout. If runout exceeds specifications, replace drive shaft assembly. Runout limit: 0.024" (0.6 mm). See Fig. 3 .
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle3.gif" title="text" alt="text"}}
2. Inspect journal axial play. If the play exceeds specifications, replace drive shaft assembly. Journal axial play: 0" (0 mm). See Fig. 4 .
{{image url="http://www.garage411.com/images/Nissan/S13/Driveline/driveaxle4.gif" title="text" alt="text"}}

Revision [936]

The oldest known version of this page was created on 2009-04-21 17:15:34 by MasterBlaster
Page History :: 2009-07-08 19:09:08 feed icon :: Owner: MasterBlaster ::
Valid XHTML 1.0 Transitional :: Valid CSS
Page was generated in 0.1102 seconds