Garage411 : HubAssemblyS2k

Revision [3420]

Last edited on 2009-07-06 17:19:11 by Spartanic23 [revised]
Additions:
=====''Honda S2000: Hub and Knuckle Assembly removal and installation''=====
Deletions:
>>{{source1}}>> =====''Honda S2000: Hub and Knuckle Assembly removal and installation''=====

Revision [3172]

Edited on 2009-06-20 13:34:15 by Spartanic23 [revised]
Additions:
>>{{source1}}>> =====''Honda S2000: Hub and Knuckle Assembly removal and installation''=====
{{sourcebigbox2}}
{{sourcebigbox2}}
~-Ball Joint Nut
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Deletions:
=====''Honda S2000: Hub and Knuckle Assembly removal and installation''=====
{{source4}}
~-Ball Joint Nut >>{{source2}}>>

Revision [2862]

Edited on 2009-06-16 20:45:09 by FreeMan [revised]
Additions:
=====''Honda S2000: Hub and Knuckle Assembly removal and installation''=====
===''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''===
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
=====''Hub and Knuckle Assembly removal and installation - Honda S2000''=====
==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''==

Revision [1509]

Edited on 2009-05-01 23:51:01 by Spartanic23
Additions:
{{source4}}
==''REMOVAL''==
Deletions:
>>{{sourceslim}}>> ==''REMOVAL''==

Revision [1343]

Edited on 2009-04-30 18:48:21 by Spartanic23
Additions:
>>{{sourceslim}}>> ==''REMOVAL''==
Deletions:
==''REMOVAL''==

Revision [1065]

Edited on 2009-04-27 19:24:02 by Spartanic23
Additions:
~-Ball Joint Nut >>{{source2}}>>
Deletions:
~-Ball Joint Nut

Revision [574]

Edited on 2009-03-24 17:00:23 by Spartanic23
Additions:
[[HondaS2000 Honda S2000]]

Revision [572]

Edited on 2009-03-24 16:53:03 by Spartanic23
Additions:
==''REMOVAL''==
==''INSTALLATION''==
To install hub/knuckle, reverse removal procedure. Tighten bolts and nuts to specification. Use NEW spindle nut, and stake after tightening.
----
==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''==
~-Ball Joint Nut
~-Upper: 29-35 (39-47)
~-Lower: 43-51 (59-69)
~-Brake Caliper Mounting Bolt: 81 (110)
~- Lower Control Arm Pivot Bolt: 58 (78)
~- Spindle Nut: 242 (329)
~- Stabilizer Bar Mounting Bolts: 29 (39)
~- Strut Assembly Shaft Nut: 22 (29)
~- Strut Fork Pinch Bolt: 32 (43)
~- Strut Fork-To-Control Arm Nut: 47 (64)
~- Tie Rod Lock Nut: 40 (54)
~- Upper Control Arm Anchor Bolt Nut: 47 (64)
~- Upper Control Arm Bushing Bolt: 97.6 (132)
~- Upper Strut Mounting Nut: 36 (49)
~- Wheel Lug Nut 80 (108)
~- Brake Line Clamp Bolt 62 **INCH Lbs.** (7.0 N.m.)

Revision [571]

Edited on 2009-03-24 16:45:03 by Spartanic23

No differences.

Revision [570]

The oldest known version of this page was created on 2009-03-24 16:44:54 by Spartanic23
Page History :: 2009-07-06 17:19:11 feed icon :: Owner: Spartanic23 ::
Valid XHTML 1.0 Transitional :: Valid CSS
Page was generated in 0.0873 seconds