Additions:
{{sourcebigbox2}}
{{sourcebigbox2}}
{{sourcebigbox2}}
{{linkunit2}}
Deletions:
{{source4}}
{{source4}}
Additions:
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Additions:
=====''Honda Civic Ignition System: coils, ignition timing and more''=====
3. Check ignition timing and adjust to specification, if necessary. To adjust, loosen distributor hold-down bolts and turn distributor housing counterclockwise to advance or clockwise to retard timing. Align pointer with Red timing mark.
===''IGNITION TIMING - Degrees BTDC @ RPM''===
Deletions:
=====''Honda Civic Ignition System''=====
3. Check ignition timing and adjust to specification, if necessary. See IGNITION TIMING table. To adjust, loosen distributor hold-down bolts and turn distributor housing counterclockwise to advance or clockwise to retard timing. Align pointer with Red timing mark.
==''IGNITION TIMING - Degrees BTDC @ RPM''==
Additions:
Disconnect 2-pin and 8-pin connectors from distributor. Disconnect spark plug wires and coil wire from distributor cap. Remove distributor hold-down bolts. Remove distributor from cylinder head. To install, coat NEW "O" ring with engine oil and put into place. To complete installation, reverse removal procedure. Set timing to specification.
==''IGNITION TIMING''==
1. Timing marks are on timing belt cover and crankshaft pulley. Start and warm engine to normal operating temperature (cooling fan comes on). Connect timing light.
2. Ignition timing check connector is located behind passenger-side kick panel. See Fig. 5 . Connect jumper wire between Brown and Black wire terminals.
3. Check ignition timing and adjust to specification, if necessary. See IGNITION TIMING table. To adjust, loosen distributor hold-down bolts and turn distributor housing counterclockwise to advance or clockwise to retard timing. Align pointer with Red timing mark.
4. Tighten distributor hold-down bolts to 16 ft. lbs. (22 N.m). Recheck timing. Remove jumper wire from ignition timing check connector.
{{image url="http://www.garage411.com/images/Honda/EGcivic/Engine/OnV5.gif" title="text" alt="text"}}
==''IGNITION TIMING - Degrees BTDC @ RPM''==
Deletions:
Disconnect 2-pin and 8-pin connectors from distributor. Disconnect spark plug wires and coil wire from distributor cap. Remove distributor hold-down bolts. Remove distributor from cylinder head. To install, coat NEW "O" ring with engine oil and put into place. To complete installation, reverse removal procedure. Set timing to specification, see bottom page.
===''IGNITION TIMING - Degrees BTDC @ RPM''===
Additions:
Disconnect 2-pin and 8-pin connectors from distributor. Disconnect spark plug wires and coil wire from distributor cap. Remove distributor hold-down bolts. Remove distributor from cylinder head. To install, coat NEW "O" ring with engine oil and put into place. To complete installation, reverse removal procedure. Set timing to specification, see bottom page.
===''IGNITION TIMING - Degrees BTDC @ RPM''===
~-1.5L Engine (D15B7):
~-Automatic tranny: 16 @ 650-750
~-Manual tranny: 16 @ 620-720
~-1.5L Engine (D15B8): 12 @ 620-720
~-1.5L Engine (D15Z1): 16 @ 550-650
~-1.6L Engine (B16A3): 16 @ 650-750
~-1.6L Engine (D16Z6):
~-Automatic tranny: 16 @ 650-750
~-Manual tranny: 16 @ 620-720
Deletions:
Disconnect 2-pin and 8-pin connectors from distributor. Disconnect spark plug wires and coil wire from distributor cap. Remove distributor hold-down bolts. Remove distributor from cylinder head. To install, coat NEW "O" ring with engine oil and put into place. To complete installation, reverse removal procedure. Set timing to specification.
Additions:
===''TORQUE SPECIFICATIONS - Ft. Lbs. (N.m)''===
~-Distributor Retaining Nuts: 18 (24)
~-Mounting Nuts: 16 (22)
~-Oxygen Sensor (O2S) 33 (45)
~-Service Bolt 16 (22)
~-Throttle Body Mounting: Nuts 16 (22)
Additions:
[[HondaCivicEg Honda Civic 1992-1995 EG and EJ]]
----
----
ECM or ECU has complete control of ignition timing. Timing is controlled in response to signals from various sensors. Input signals from TDC, CRANK and CYL, throttle angle, coolant temperature, and MAP sensors are all used by ECM to determine optimum ignition timing control.
==''DISTRIBUTOR REMOVAL AND INSTALLATION''==
Disconnect 2-pin and 8-pin connectors from distributor. Disconnect spark plug wires and coil wire from distributor cap. Remove distributor hold-down bolts. Remove distributor from cylinder head. To install, coat NEW "O" ring with engine oil and put into place. To complete installation, reverse removal procedure. Set timing to specification.
{{image url="http://www.garage411.com/images/Honda/EGcivic/Engine/adj1.gif" title="text" alt="text"}}
==''IGNITION COIL REMOVAL AND INSTALLATION''==
Ensure ignition switch is in OFF position. Remove distributor cap, cap seal and leak cover. Remove 2 screws to disconnect Black/Yellow and White/Blue wires from coil primary terminals. Remove 2 mounting screws. Slide ignition coil out of distributor housing.
----
----
[[HondaCivicEg Honda Civic 1992-1995 EG and EJ]]
Deletions:
[[HondaCivicEg Honda Civic 1992-1995 EG]]
ECM has complete control of ignition timing. Timing is controlled in response to signals from various sensors. Input signals from TDC, CRANK and CYL, throttle angle, coolant temperature, and MAP sensors are all used by ECM to determine optimum ignition timing control.
Deletions:
----
Additions:
{{source4}}
Deletions:
Honda Civic 1992-1995 EG