No differences.
Additions:
{{sourcebigbox2}}
{{sourcebigbox2}}
===''IGNITION SWITCH''===
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Deletions:
{{source4}}
>>{{source2}}>> ===''IGNITION SWITCH''===
Additions:
Ignition Timing: 5° +/- 2° BTDC (RED mark) at idle in Neutral
>>{{source2}}>> ===''IGNITION SWITCH''===
Deletions:
Ignition Timing: 5° +/- 2° BTDC (RED mark (B)) at idle in Neutral
>>{{source2}}>> ====''IGNITION SWITCH''====
Additions:
=====''Honda S2000 2000-2004 AP1: Ignition System''=====
===''COMPONENTS''===
{{image url="http://www.garage411.com/images/Honda/Ap1/AP1_Ignitioncomp.gif" title="text" alt="text"}}
===''CIRCUIT DIAGRAM''===
{{image url="http://www.garage411.com/images/Honda/Ap1/Ap1_IgnitionCircuit.gif" title="text" alt="text"}}
6. Aim the light toward the pointer. Check the ignition timing under no load conditions: headlights, blower fan, and air conditioner are not operating. If the ignition timing differs from the specification below, replace the Engine Control Module (ECM).
[[http://www.garage411.com/images/Honda/Ap1/InspecElectrode.gif Inspecting Electrodes and Ceramic Insulator]]
2. Do not adjust the gap of platinum tip plugs; replace the spark plug if the gap is out of specification.
3. Replace the plug at the specified interval, or if the center electrode is rounded. Use only the spark plugs listed.
>>{{source2}}>> ====''IGNITION SWITCH''====
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
=====''Ignition System - Honda S2000 2000-2004 AP1''=====
[[http://www.garage411.com/images/Honda/Ap1/AP1_Ignitioncomp.gif Honda S2000 Ignition System Components]]
[[http://www.garage411.com/images/Honda/Ap1/Ap1_IgnitionCircuit.gif Honda S2000 Ignition System Circuit Diagram]]
6. Aim the light toward the pointer (A). Check the ignition timing under no load conditions: headlights, blower fan, and air conditioner are not operating. If the ignition timing differs from the specification below, replace the Engine Control Module (ECM).
[[http://www.garage411.com/images/Honda/Ap1/InspecElectrode.gif Inspecting Electrodes & Ceramic Insulator]]
2. Do not adjust the gap of platinum tip plugs (A); replace the spark plug if the gap is out of specification.
3. Replace the plug at the specified interval, or if the center electrode is rounded (A). Use only the spark plugs listed.
>>{{source2}}>> =====''Ignition Switch''=====
No differences.
Additions:
SRS components are located in this area. Review the SRS component locations, and precautions, and procedures before performing repairs or service.
Deletions:
SRS components are located in this area. Review the SRS component locations , and precautions, and procedures before performing repairs or service.
Additions:
{{source4}}
>>{{source2}}>> =====''Ignition Switch''=====
Deletions:
>>{{source2}}>>
>>{{sourceslim}}>> =====''Ignition Switch''=====
Additions:
>>{{sourceslim}}>> =====''Ignition Switch''=====
Deletions:
=====''Ignition Switch''=====
Additions:
>>{{source2}}>>
The oldest known version of this page was created on
2009-03-23 19:44:14 by Spartanic23
[Cloned from S2kIgnition]