Additions:
=====''Honda S2000 2000-2004 AP1: Lubrication System''=====
Deletions:
>>{{source1}}>> =====''Honda S2000 2000-2004 AP1: Lubrication System''=====
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Additions:
>>{{source1}}>> =====''Honda S2000 2000-2004 AP1: Lubrication System''=====
{{sourcebigbox2}}
==''OIL FILTER REPLACEMENT''==
{{sourcebigbox2}}
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Deletions:
=====''Honda S2000 2000-2004 AP1: Lubrication System''=====
{{source4}}
>>{{source1}}>> ==''OIL FILTER REPLACEMENT''==
{{source4}}
Additions:
=====''Honda S2000 2000-2004 AP1: Lubrication System''=====
{{image url="http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif" title="text" alt="text"}}
**Removing Oil Jet**
{{image url="http://www.garage411.com/images/Honda/Ap1/OilJetRemoving.gif" title="text" alt="text"}}
Deletions:
=====''Lubrication System - Honda S2000 2000-2004 AP1''=====
[[http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif Honda S2000 Lubrication System]]
[[http://www.garage411.com/images/Honda/Ap1/OilJetRemoving.gif Removing Oil Jet]]
Additions:
1. Remove the [[http://www.garage411.com/images/Honda/Ap1/YelRedWire.gif YEL/RED wire]]from the engine oil pressure switch.
2. Check for continuity between the positive terminal and the engine (ground). There should be continuity with the engine stopped. There should be no continuity with the engine running.
2. Remove the engine oil pressure switch, and install an [[http://www.garage411.com/images/Honda/Ap1/OilPressGauge.gif oil pressure gauge]].
2. Remove the [[http://www.garage411.com/images/Honda/Ap1/OilDrainBolt.gif drain bolt]], and drain the engine oil.
3. Reinstall the drain bolt with a new washer.
2. Inspect the threads and rubber seal on the new [[http://www.garage411/images/Honda/Ap1/OilFilter.gif filter]]. Wipe off the seat on the engine block, then apply a light coat of new engine oil to the filter rubber seal. Use only filters with a built-in bypass system.
~-Make sure that a 1.5 mm (0.06 in.) diameter drill will go through the nozzle hole (1.6 mm (0.06 in.) diameter).
~-Make sure the check ball moves smoothly and has a stroke of approximately 4.0 mm (0.16 in.).
===''HONDA S2000 OIL PUMP OVERHAUL''===
5. [[http://www.garage411.com/images/Honda/Ap1/OilPumpRemoval.gif Remove the oil pump]] oil pump chain, and crankshaft sprocket.
7. Check the [[http://www.garage411.com/images/Honda/Ap1/oil16.gif inner-to-outer rotor radial clearance]] between the inner rotor and outer rotor. If the inner-to-outer rotor radial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
8. Check the [[http://www.garage411.com/images/Honda/Ap1/oil17.gif housing-to-rotor axial clearance]] between the rotor and pump housing. If the housingto-rotor axial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
9. Check the [[http://www.garage411.com/images/Honda/Ap1/oil18.gif housing-to-outer rotor radial clearance]] between the outer rotor and pump housing. If the housing-to-outer rotor radial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
11. Installation : Squeeze the new [[http://www.garage411.com/images/Honda/Ap1/oil19.gif oil pump chain tensioner]]then install the set clip on it as shown. The set clip is supplied with the oil pump chain tensioner.
12. Install the [[http://www.garage411.com/images/Honda/Ap1/oil20.gif crankshaft sprocket]]oil pump chain, and oil pump.
15. Set the crankshaft sprocket so that the No. 1 piston is at top dead center (TDC). [[http://www.garage411.com/images/Honda/Ap1/oil23.gif Align the key]]on the sprocket and crankshaft with the pointer on the cylinder block.
16. Move the [[http://www.garage411.com/images/Honda/Ap1/oil24.gif cam chain]] so that the colored piece aligns with the punched mark on the crankshaft sprocket.
17. Install the [[http://www.garage411.com/images/Honda/Ap1/oil25.gif oil pump chain guide]]and oil pump chain tensioner.
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
1. Remove the [[http://www.garage411.com/images/Honda/Ap1/YelRedWire.gif YEL/RED wire]] (A) from the engine oil pressure switch (B).
2. Check for continuity between the positive terminal (C) and the engine (ground). There should be continuity with the engine stopped. There should be no continuity with the engine running.
2. Remove the engine oil pressure switch, and install an [[http://www.garage411.com/images/Honda/Ap1/OilPressGauge.gif oil pressure gauge]] (A).
2. Remove the [[http://www.garage411.com/images/Honda/Ap1/OilDrainBolt.gif drain bolt]] (A), and drain the engine oil.
3. Reinstall the drain bolt with a new washer (B).
2. Inspect the threads (A) and rubber seal (B) on the new [[http://www.garage411/images/Honda/Ap1/OilFilter.gif filter]]. Wipe off the seat on the engine block, then apply a light coat of new engine oil to the filter rubber seal. Use only filters with a built-in bypass system.
~-Make sure that a 1.5 mm (0.06 in.) diameter drill will go through the nozzle hole (A) (1.6 mm (0.06 in.) diameter).
~-Make sure the check ball (B) moves smoothly and has a stroke of approximately 4.0 mm (0.16 in.).
====''HONDA S2000 OIL PUMP OVERHAUL''====
5. [[http://www.garage411.com/images/Honda/Ap1/OilPumpRemoval.gif Remove the oil pump]] (A), oil pump chain (B), and crankshaft sprocket (C).
7. Check the [[http://www.garage411.com/images/Honda/Ap1/oil16.gif inner-to-outer rotor radial clearance]] between the inner rotor (A) and outer rotor (B). If the inner-to-outer rotor radial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
8. Check the [[http://www.garage411.com/images/Honda/Ap1/oil17.gif housing-to-rotor axial clearance]] between the rotor (A) and pump housing (B). If the housingto-rotor axial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
9. Check the [[http://www.garage411.com/images/Honda/Ap1/oil18.gif housing-to-outer rotor radial clearance]] between the outer rotor (A) and pump housing (B). If the housing-to-outer rotor radial clearance exceeds the service limit, replace the outer rotor and oil pump housing.
11. Installation : Squeeze the new [[http://www.garage411.com/images/Honda/Ap1/oil19.gif oil pump chain tensioner]] (A), then install the set clip (B) on it as shown. The set clip is supplied with the oil pump chain tensioner.
12. Install the [[http://www.garage411.com/images/Honda/Ap1/oil20.gif crankshaft sprocket]] (A), oil pump chain (B), and oil pump (C).
15. Set the crankshaft sprocket so that the No. 1 piston is at top dead center (TDC). [[http://www.garage411.com/images/Honda/Ap1/oil23.gif Align the key]] (A) on the sprocket and crankshaft with the pointer (B) on the cylinder block.
16. Move the [[http://www.garage411.com/images/Honda/Ap1/oil24.gif cam chain]] so that the colored piece (A) aligns with the punched mark (B) on the crankshaft sprocket.
17. Install the [[http://www.garage411.com/images/Honda/Ap1/oil25.gif oil pump chain guide]] (A) and oil pump chain tensioner (B).
Additions:
>>{{source1}}>> ==''OIL FILTER REPLACEMENT''==
====''HONDA S2000 OIL PUMP OVERHAUL''====
Deletions:
==''OIL FILTER REPLACEMENT''==
>>{{sourcebigbox}}>> ====''HONDA S2000 OIL PUMP OVERHAUL''====
{{sourceslim}}
No differences.
No differences.
No differences.
Additions:
[[http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif Honda S2000 Lubrication System]]
>>{{sourcebigbox}}>> ====''HONDA S2000 OIL PUMP OVERHAUL''====
Deletions:
[[http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif Honda S2000 Lubrication System]] >>{{source2}}>>
====''HONDA S2000 OIL PUMP OVERHAUL''====
Additions:
{{sourceslim}}
Additions:
[[http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif Honda S2000 Lubrication System]] >>{{source2}}>>
{{source4}}
Deletions:
[[http://www.garage411.com/images/Honda/Ap1/Ap1_LubeSystem.gif Honda S2000 Lubrication System]]
The oldest known version of this page was created on
2009-03-23 19:44:03 by Spartanic23
[Cloned from S2kLubrication]