Additions:
4. Insert the feeler gauge between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
Deletions:
<<{{source2}}<< 4. Insert the feeler gauge between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
{{source4}}
Additions:
{{sourcebigbox2}}
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Additions:
7. Rotate the [[CrankshaftS2k crankshaft]] 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj65.gif See image]].
9. Rotate the [[CrankshaftS2k crankshaft]] 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj66.gif See image]].
11. Rotate the [[CrankshaftS2k crankshaft]] 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj67.gif See image]].
13. Install the [[CylinderHeadS2k cylinder head cover]].
Deletions:
7. Rotate the crankshaft 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj65.gif See image]].
9. Rotate the crankshaft 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj66.gif See image]].
11. Rotate the crankshaft 180° clockwise (camshaft gears turn 90°). [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj67.gif See image]].
13. Install the cylinder head cover.
Additions:
----
----
**TIP:** Adjust the valves only when the cylinder head temperature is less than 100°F (38°C).
1. Remove the [[CylinderHeadS2k cylinder head cover]].
2. Set the No. 1 piston at top dead center (TDC). The TDC marks on the cam chain sprocket should align with the cylinder head surface. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj61.gif See image]].
{{image url="http://www.garage411.com/images/Honda/Ap1/Engine/valveadj62.gif" title="text" alt="text"}}
<<{{source2}}<< 4. Insert the feeler gauge between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
5. If you feel too much or too little drag, loosen the locknut, and turn the adjusting screw until the drag on the feeler gauge is correct. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj64.gif See image]].
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
----
----
Deletions:
**TIP: Adjust the valves only when the cylinder head temperature is less than 100°F (38°C).**
1. Remove the cylinder head cover.
2. Set the No. 1 piston at top dead center (TDC). The TDC marks (A) on the cam chain sprocket should align with the cylinder head surface. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj61.gif See image]].
{{image url="http://www.garage411.com/images/Honda/Ap1/Engine/valveadj62.gif" title="text" alt="text"}}~-
<<{{source2}}<< 4. Insert the feeler gauge (A) between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
5. If you feel too much or too little drag, loosen the locknut (A), and turn the adjusting screw (B) until the drag on the feeler gauge is correct. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj64.gif See image]].
Additions:
<<{{source2}}<< 4. Insert the feeler gauge (A) between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
Deletions:
4. Insert the feeler gauge (A) between the adjusting screw and the end of the valve stem and slide it back and forth; you should feel a slight amount of drag. [[http://www.garage411.com/images/Honda/Ap1/Engine/valveadj63.gif See image]].
----
{{sourceslim}}
Additions:
{{sourceslim}}
Additions:
[[HondaS2000 Honda S2000 AP1 F20C]]
{{source4}}
Deletions:
Honda S2000 AP1 F20C
[[HondaS2000 Honda S2000]]
Additions:
----
[[HondaS2000 Honda S2000]]