Additions:
=====''Honda S2000 Wheel Bearing Removal and Installation''=====
Deletions:
>>{{source1}}>> =====''Honda S2000 Wheel Bearing Removal and Installation''=====
Additions:
~- REAR: 220
Deletions:
~- REAR: 181 (245)
Additions:
>>{{source1}}>> =====''Honda S2000 Wheel Bearing Removal and Installation''=====
{{sourcebigbox2}}
{{sourcebigbox2}}
===''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''===
[[HondaS2000 Honda S2000 AP1]]
{{linkunit2}}
Deletions:
=====''Honda S2000 Wheel Bearing Removal and Installation''=====
{{source4}}
>>{{sourcebigbox}}>> ===''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''===
{{sourceslim}}
Additions:
===''FRONT''===
===''REAR REMOVAL AND INSTALLATION''===
1. Raise and support vehicle. Remove [[HubAssemblyS2k hub and bearing assembly]]. Using Hub Remover/Installer (07GAF-SD40100) separate hub from knuckle and hydraulic press. Hold hub and keep it from falling when pressed clear. Remove 3 screws attaching splash guard and bearing retaining snap ring from knuckle. Press wheel bearing out of knuckle, using Driver (07749-0010000) and Attachment (07749-0010400). Press wheel bearing inner race from hub, using Hub Remover/Installer (07GAF-SD40100) and hydraulic press. Clean knuckle and hub thoroughly before reassembly.
>>{{sourcebigbox}}>> ===''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''===
~- Strut Shaft Nut: 22 (29) (REAR SUSPENSION)
**Did you find this repair info helpful or are improvements needed? Please leave comments below.**
Deletions:
====''FRONT''====
====''REAR''====
**REMOVAL AND INSTALLATION**
1. Raise and support vehicle. Remove hub and bearing assembly. See HUB & BEARING ASSEMBLY. Using Hub Remover/Installer (07GAF-SD40100) separate hub from knuckle and hydraulic press. Hold hub and keep it from falling when pressed clear. Remove 3 screws attaching splash guard and bearing retaining snap ring from knuckle. Press wheel bearing out of knuckle, using Driver (07749-0010000) and Attachment (07749-0010400). Press wheel bearing inner race from hub, using Hub Remover/Installer (07GAF-SD40100) and hydraulic press. Clean knuckle and hub thoroughly before reassembly.
>>{{sourcebigbox}}>> ==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''==
~- Strut Shaft Nut: 22 (29) (REAR SUSPENSION0
Additions:
{{sourceslim}}
Additions:
=====''Honda S2000 Wheel Bearing Removal and Installation''=====
Deletions:
=====''Wheel Bearing - Honda S2000''=====
Additions:
{{source4}}
====''FRONT''====
>>{{sourcebigbox}}>> ==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''==
Deletions:
====''FRONT''==== >>{{source2}}>>
==''TORQUE SPECIFICATIONS Ft. Lbs. (N.m)''==
{{sourceslim}}
Additions:
{{sourceslim}}
No differences.
Additions:
====''FRONT''==== >>{{source2}}>>
Deletions:
====''FRONT''====
Additions:
**REMOVAL**
**INSTALLATION**
**REMOVAL AND INSTALLATION**
Deletions:
==''REMOVAL''==
==''INSTALLATION''==
==''REMOVAL AND INSTALLATION''==
Additions:
~- Lower Ball Joint Nut: 51-58 (69-78) (REAR SUSPENSION)
~- Spindle Nut
~- FRONT: 242 (329)
~- REAR: 181 (245)
~- Stabilizer Bar Mounting Bolts:
~- FRONT: 29 (39)
~-REAR: 40 (54)
~- Stabilizer Link Nut 22 (29) (REAR SUSPENSION)
~- Strut-To-Lower "A" Arm Bolt: 47 (64) (REAR SUSPENSION)
~- Strut Mount Base: (2) 36 (49)
~- Strut Shaft Nut: 22 (29) (REAR SUSPENSION0
~- Upper Arm-To-Body Bolt 97.6 (132) (REAR SUSPENSION)
~- Upper Ball Joint Nut: 36-43 (49-59) (REAR SUSPENSION)
Deletions:
~- Spindle Nut: 242 (329)
~- Stabilizer Bar Mounting Bolts: 29 (39)
Additions:
2. Press NEW bearing onto hub by using old bearing and Support Base (07965-SD90100). Install splash guard and bearing retaining snap ring to knuckle. Install hub onto knuckle by using Support Base (07965-SD90100), Attachment (07746-0010500) and Driver (07749-0010000). Reverse removal procedures for hub and bearing assembly. Tighten fasteners to specification. Stake hub retaining nut against spindle.
Deletions:
2. Press NEW bearing onto hub by using old bearing and Support Base (07965-SD90100). Install splash guard and bearing retaining snap ring to knuckle. Install hub onto knuckle by using Support Base (07965-SD90100), Attachment (07746-0010500) and Driver (07749-0010000). Reverse removal procedures for hub and bearing assembly. Tighten fasteners to specification. See TORQUE SPECIFICATIONS . Stake hub retaining nut against spindle.
Additions:
====''FRONT''====
====''REAR''====
Deletions:
====''FRONT WHEEL BEARING''====
====''REAR WHEEL BEARING''====
No differences.
Additions:
====''FRONT WHEEL BEARING''====
====''REAR WHEEL BEARING''====
==''REMOVAL AND INSTALLATION''==
1. Raise and support vehicle. Remove hub and bearing assembly. See HUB & BEARING ASSEMBLY. Using Hub Remover/Installer (07GAF-SD40100) separate hub from knuckle and hydraulic press. Hold hub and keep it from falling when pressed clear. Remove 3 screws attaching splash guard and bearing retaining snap ring from knuckle. Press wheel bearing out of knuckle, using Driver (07749-0010000) and Attachment (07749-0010400). Press wheel bearing inner race from hub, using Hub Remover/Installer (07GAF-SD40100) and hydraulic press. Clean knuckle and hub thoroughly before reassembly.
2. Press NEW bearing onto hub by using old bearing and Support Base (07965-SD90100). Install splash guard and bearing retaining snap ring to knuckle. Install hub onto knuckle by using Support Base (07965-SD90100), Attachment (07746-0010500) and Driver (07749-0010000). Reverse removal procedures for hub and bearing assembly. Tighten fasteners to specification. See TORQUE SPECIFICATIONS . Stake hub retaining nut against spindle.
Additions:
[[HondaS2000 Honda S2000]]